Epson Stylus Photo R280 Error
Flashes at intervals of 1.25 seconds. Flashes as follows ON 0.5 sec. - OFF 0.5 sec. - ON 0.5 sec. - OFF 1.0 sec. Flashes at intervals of 0.5 seconds. Flashes at intervals of 1.25 seconds. Figure 3-2. Error Indication on EPSON Status Monitor 3 Figure 3-2. Error Indication on EPSON Status Monitor 3 NOTE The part number of the Ink Cartridges shown in the Status Monitor 3 screen differs by destination.
APG Unit
Parts Components need to be removed in advance Printer Cover Paper Support Assy Upper Housing 1. Remove the two screws taking care not to lose the gears, and remove the APG Unit. Screw C.B.S. M3x6 tightening torque 7-9 kgf.cm No.1 The numbers shown in the figure indicate the order of tightening the screws. 2. Remove the Combination Gear 10, 15.2 . Figure 4-56. Removing the Combination Gear 10, 15.2 Figure 4-56. Removing the Combination Gear 10, 15.2 Lubrication is required. See the page given...
Required Adjustments
The table below lists the required adjustments depending upon the parts being repaired or replaced. Find the part s you removed or replaced, and check which adjustment s must be carried out. Note lt Meaning of the marks in the table gt O indicates that the adjustment must be carried out. O indicates that the adjustment is recommended. --- indicates that the adjustment is not required. If you have removed or replaced multiple parts, make sure to check the required adjustments for the all parts....
I Lqt
Be careful not to damage the Pinion Gear of the PF Motor. Parts Components need to be removed in advance Printer Cover Paper Support Assy Upper Housing Main Board Unit 1. Disconnect the FFC of the PF Encoder from CN1 connector. 2. Remove the screw and remove the PF Encoder. Screw C.B.P. M2.6x8 tightening torque 3.5-4.5 kgf.cm No.5 3. Peel off the double-sided tape attached to the center part, and remove the PF Scale. Figure 4-80. Removing the PF Encoder PF Scale Figure 4-80. Removing the PF...
Ffc
3. Peel off the four acetate tapes that secures the following cables on the back of the Main Board Unit. Figure 4-18. Removing the Main Board Unit 1 Figure 4-18. Removing the Main Board Unit 1 Table 4-5. List of Connectors and their Destinations
Panel Assy Cover Open Sensor
Parts Components need to be removed in advance Printer Cover Paper Support Assy Housing Upper 1. Peel off the acetate tape C. 2. Disconnect the Panel FFC from the connector CN5 on the Main Board and peel the Panel FFC off the Cable Holder Frame. 3. Disconnect the CDR Sensor Cable and Cover Open Sensor Cable from the connectors CN4, CN17 on the Main Board. 4. Release the CDR Sensor Cable and Cover Open Sensor Cable from the two hooks of the Cable Holder Frame. 5. Peel off the acetate tape A, B...
Info Jzz
Flowchart 4-1. R280 R285 R290 Disassembly Flowchart 4.2 Removing Exterior Parts Components 4.2.1 Printer Cover Parts Components need to be removed in advance Nothing 1. Pull out the left shaft and right shaft of the Printer Cover, and remove the Printer Cover. Figure 4-9. Removing the Printer Cover Figure 4-9. Removing the Printer Cover Parts Components need to be removed in advance Nothing
Stacker Assy Stacker Cover
Parts Components need to be removed in advance Nothing 3. Release the Stacker Cover from the two shafts and remove the Stacker Cover. Figure 4-12. Removing the Stacker Assy Stacker Cover Figure 4-12. Removing the Stacker Assy Stacker Cover When installing the Stacker Assy, insert the guide pins of the Stacker Assy into the lower grooves of the Guide Stacker Assy. The upper grooves are used when CDR is printed. Figure 4-13. Installing the Stacker Assy Figure 4-13. Installing the Stacker Assy
Info Yhr
The printer does not work at all after power-on. LEDs do not light up. Table 3-17. Troubleshooting Power Problems Table 3-17. Troubleshooting Power Problems Replace the power code with a new one. Does the printer work normally The power code is defective. Use the new one. Do the power supplied from the AC line match with the electrical requirements of the printer Use an AC line that matches the printer electrical requirements. Poor connection of the PS Assy connector Is the PS Assy connector...
Top Margin Adjustment
Patterns are printed as shown below. The distance from a paper top edge to a line is 4 mm or more Choose the - from a combobox. 2 mm or less Choose the from a combobox. Figure 5-1. Top Margin Adjustment Pattern Measure the distance from the top edge of paper to the printed line, and enter any one of the -, 0, according to the judging standard.
Electrical Circuits
The electric circuit diagrams below are shown at the following pages Stylus Photo R280 R285 R290 Board C691 MAIN Rev. A Sheet 1 1 Stylus Photo R280 R285 R290 Board C691 MAIN Rev. A Sheet 1 1
Info Rhd
The thickness gauge to be used must be free from dust and dirt and from deformation. Be sure to clean it before use. Take care that the Print Head is not soiled or scratched. To ensure high accuracy of adjustment, install new ink cartridges in the carriage, and move the carriage right and left by pulling the belt without holding the carriage. Make this adjustment after installing the mechanism unit in the Housing Lower. Install the Linear Scale after adjustment. Refer to 4.4.1 Removing the...
Info Uwn
Check all connections and make sure all devices are on. If the power was turned off during printing, cancel the print job. If the error does not clear, see your printer documentation. The printer cannot communicate with the PC properly. Delete all print jobs and turn the printer off. Remove any foreign objects from inside the printer. After a few minutes, turn the printer back on. Parts inside your printer are at the end of their service life. See your printer documentation.
Servicing Adjustment Item List
The adjustment items of this product are as follows. Install the Head Nozzle surface parallel to the printing surface and set the gap between the paper and the Head Nozzle surface to the specified value. Mechanical adjustment using the thickness gauges. Make a proper adjustment according to the result whether the manually-moved carriage printhead runs over or hits against the gauges placed on the platen. When the main board needs to be replaced, use this to copy adjustment values stored on the...
Info Tpp
Fold the vinyl sheet in half and insert the folded sheet between the Paper Support Assy and the Printer Cover with the folded side facing the front side of the printer, and secure the sheet with the strong tape as shown below. Attach the left and right tapes to the Paper Support Assy and the side of the housing. Figure 4-4. Securing the Paper Support Assy Securing the Stacker Cover tape 60mm x 1 pc., fold one end by 5mm Have a commercially available 280mm-width x 80mm-length vinyl sheet to...
Epson Printer R230 Roller Spring
1. Is the ASF Unit installed incorrectly Even though the printer performs paper feeding operation, the paper is not fed into the printer. 1. Is the ASF Unit installed incorrectly 2. Is the Paper Return Lever not moving properly during the feeding operation 1. Is the Torsion Spring 0.22 attached incorrectly 1. Is the Torsion Spring 0.22 attached incorrectly 2. Install the Paper Return Lever and the Torsion Spring 6.45 correctly. 1. Install the PE Sensor Lever and Torsion Spring 0.22 correctly....
EJ Frame Assy
Parts Components need to be removed in advance Printer Cover Paper Support Assy Upper Housing Main Board Unit Panel Assy Cover Open Sensor Printer Mechanism 1. Move the CR Unit to the home position side. 2. Release the Head FFC from the two hooks of the Cable Holder Frame and pull out the Head FFC through the cutout. 3. Release the Head FFC from the three hooks of the Front Frame and peel off the double-sided tape. Head FFC Double-sided Tape Hook 4. Disconnect the PF Encoder FFC from the PF...
Cr Home Position R290
Power the printer and turn it off forcedly by disconnecting the power cable when the CR Unit is unlocked and moved away from the home position. Turn the EJ Roller gear on the left side of the printer in the direction of the arrow until the carriage is unlocked. Figure 4-8. How to Unlock the Carriage Figure 4-8. How to Unlock the Carriage The flowchart below shows step-by-step disassembly procedures. When disassembling each unit, refer to the page number shown in the figure. Panel Assy Cover...