Cif
Features common to R260 R265 R270 and R360 R380 R390 The circuits support multi-common printing method that achieves high-speed printing reducing the number of carriage movements. Features of C658Main Board R360 R380 R390 The CPU incorporates an ASIC for controlling memory cards. The ASIC achieves high-speed access to a card. Employs SOC06H that incorporates one main processor and six image processing processors enabling concurrent processing for printing. 16-bit DDR1-SDRAM 166 MHz memory for...
Info Crs
For sheets of paper, set the front tray to the paper position by pulling up the tray lever. For a CD or DVD, set the front tray to the CD DVD position by pushing down the tray lever. The CDR guide status does not match with the print setting. The front tray is not in the CD DVD position. Push down the tray lever to raise the front tray to the CD DVD position. For sheets of paper, turn off the printer and then remove any jammed paper by hand. For a CD or DVD, remove the CD DVD tray. Next, press...
Info Ite
Removing the Main Board Unit p.78 The CDR Guide is set correctly, but the error occurs. 1. Is the CDR Guide Detection Assy cable not connected to the Main Board 1. Connect the cable to the Main Board. R360 R380 R390 Main Board CN9 R260 R265 R270 Main Board CN4 4.5.15 CDR Guide Detection Assy p.111 2. Replace the CDR Guide Detection Assy. 3. Is the CDR Guide Detection Assy cable broken 3. Replace the CDR Guide Detection Assy. 1. Is the CDR Guide Lever not installed correctly 1. Install the CDR...
Info Atb
Make this adjustment after installing the mechanism unit in the Housing Lower. Install the Linear Scale after adjustment. Refer to 4.4 Removing the Printer Mechanism p. 87 With EPSON Stylus Photo R260 R265 R270, R360 R380 R390, four stages of PG setting are available by means of the APG Mechanism. However, make this adjustment with the mechanism in the minimum PG position PG- 1.2 mm . Refer to 4.5.2 APG Unit p. 90 and below. Figure 5-8. PG Position at PG Adjustment Figure 5-8. PG Position at PG...
I Cdv
Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. 4.1.8 Sharp Metal Edges Danger p.62 Take extra care not to spill ink and contaminate the surroundings. Also, when removing the Waste Ink Tube, be careful not to spill the ink. Extra care must be taken to avoid injury from sharp edges of the rib of the Main Frame. Be careful not to drop and damage the shaft of the Carriage Lock and the Torsion Spring, as they easily...
Removing the Main Board Unit
Parts Components need to be removed in advance All exterior parts components USB Board R260 R265 R270 only 1. Disconnect all FFCs and connector cables from the Main board. 2. Remove the all cables from the cable retainer on the Main Board. Figure 4-51. Removing the Cables R360 R380 R390 Main Board Figure 4-51. Removing the Cables R360 R380 R390 Main Board Figure 4-52. R360 R380 R390 Main Board Figure 4-52. R360 R380 R390 Main Board For R260 R265 R270, when removing the connector cables, also...
Assembling Point Epson Stylus Photo R220 R230 Service Manual
1. Is the ASF Unit installed incorrectly Even though the printer performs paper feeding operation, the paper is not fed into the printer. 1. Is the ASF Unit installed incorrectly 2. Is the Paper Return Lever not moving properly during the feeding operation 1. Is the Torsion Spring 0.22 attached incorrectly 1. Is the Torsion Spring 0.22 attached incorrectly 2. Install the Paper Return Lever and the Torsion Spring 6.45 correctly. 1. Install the PE Sensor Lever and Torsion Spring 0.22 correctly....