PF motor removal
1. Remove the Housing from the printer. Refer to Section 4.2.1. 2. Remove the Waste drain ink pad unit from the printer. Refer to Section 4.2.6. 3. Remove the Front frame and Paper eject roller. Refer to Section 4.2.10. 4. Remove the Plain washer and then remove the Combination gear 11.6, 36.8 Figure 4-41. Removing the Plain washer and Combination gear 11.6, 36.8 Figure 4-41. Removing the Plain washer and Combination gear 11.6, 36.8 5. Remove three nuts Hexagon Nut M3 securing the PF motor to...
T
Figure 1-7. Printable Area for Envelopes Storage Temperature Storage Packing Transit ISO IEC 10561 Letter Pattern at 360 dpi 2 years from date of production -20 C to 40 C within a month at 40 C -30 C to 40 C within a month at 40 C -30 C to 60 C within 120 hours at 60 C and within a month at 40 C 28.1 mm W x 66.85 mm D x 43.3 mm H Print Capacity 300 pages A4 360 dpi, 5 duty each color Ink Life 2 years from date of production Storage -20 C to 40 C within a month at 40 C Packing -30 C to 40 C...
Printhead removal
1. Remove the Housing from the printer. Refer to Section 4.2.1. 2. Open the Cover Cartridge and remove the both black and color ink cartridge. 3. Remove the Cover Cartridges for black and color ink cartridges from the CR Assembly. 4. Remove the Head FFC Holder from the CR Assembly by releasing two hooks. Figure 4-7. Removing the Head FFC Holder Figure 4-7. Removing the Head FFC Holder 5. Disconnect the Printhead's FFC from the connector on the Printhead. 6. Remove two screws C.B.P-TITE 3x6 F Zn...
Adjustment Program Execution Adjustment Program Initial Setting menu
You have to input the following four items before entering the adjustment main menu. Model name Stylus COLOR 680 777 777i For the Stylus COLOR 685, select Model name Stylus COLOR 680 for the Stylus COLOR 777i, select Model name Stylus COLOR 777. Interface setting LPT1, LPT2, LPT3, EPUSB1, EPUSB2, EPUSB3 Destination EURO ASIA, EAI Follow the procedure below to input the initial settings. 1. When you run this program, the following menu appears. Select the Stylus COLOR 680 or 777 777i in the...
Electrical Circuits
The electric circuit diagrams below are shown at the following pages C383MAIN control circuit board C383MAIN-B control circuit board C383PSE power supply circuit board C383PNL panel circuit board MODEL SC 600 111 lili BOARD C3B3MAIN BOHAD SHEET i i REV. 0 MODEL SC 68D III IIIi BOARD C383MAIN-B BOHAD SHEET i i MODEL sc 680 777 BOARD C383PSD BORAD SHDD7 1 1 RDV- D
Head Cleaning Operation
With this sequence, you can forcibly solve the clogged nozzle problem caused by viscous ink. This program performs powerful cleanig forcibly. If you can not recover the clogged nozzles despite you performed this cleaning operation, enter the Initial ink charge sequence by referring to Section 5.1.9. 1. Choose the Head cleaning in the Maintenance menu as following figure. 1. Choose the Head cleaning in the Maintenance menu as following figure. Figure 5-16. Choose the Maintenance menu Figure...
Component Layout
Figure 7-2. C383MAIN Component Layout Parts Side Figure 7-2. C383MAIN Component Layout Parts Side Figure 7-3. C383 MAIN B Component Layout Figure 7-5. C383PSE Component Layout Figure 7-5. C383PSE Component Layout Figure 7-4. C383PSB Component Layoout
Circuit board removal
1. Remove the Housing from the printer. Refer to Section 4.2.1. 2. Remove three screws C.B.S 3x6 F Zn securing the Circuit board unit at the front 2. Remove three screws C.B.S 3x6 F Zn securing the Circuit board unit at the front Figure 4-16. Removing four screws at the printer front side 3. Remove four screws C.B.S 3x6 F Zn securing the Circuit board unit at the back side of the Printer mechanism and remove two screws C.B.S 3x6 F Zn securing the Circuit board unit at the right side viewed from...
Waste drain ink pad unit removal
1. Remove the Housing from the printer. Refer to Section 4.2.1. 2. Remove one screw C.B.P-TITE 3x8 F Zn on the front right side of the printer. 3. Remove two screws C.B.P- TITE 3x8 F Zn and take some cables off from the cable hook in the Waste drain ink pad unit as shown in the following figure. Figure 4-13. Removing one screw securing the Waste ink pad unit Figure 4-13. Removing one screw securing the Waste ink pad unit 3. Remove two screws C.B.P- TITE 3x8 F Zn and take some cables off from...
Head ID Input
This adjustment function is required when any of the following parts is replaced. This adjustment function enables you to write printhead ID into the specific address of the EEPROM. This operation is considered the most important to maintain proper ink discharging system. If any ID is not written correctly, it results in white or color lines and also gives bad influence on dot weight. Before or after performing this operation, refer to the Table 5-2 and perform any appropriate adjustments or...
BiD Adjustment
You perform this adjustment to correct differences in printing positions, which is caused by incorrect of printing timing in right and left directions during the Bidirectional printing. Therefore, you are required to perform this adjustment after performing the following operations. Replacing the Print mechanism Replacing the Carriage Assembly Figure 5-7. Error message in the Input head ID menu 1. Choose the Bi-directional in the Adjustment main menu as following figure. 1. Choose the...
Overview
This section describes the operating principles of the printer mechanism and electrical circuit boards. The Stylus COLOR 680 777 777i has the following boards Main board C383 MAIN C383 MAIN-B NOTE C383 MAIN-B is compatible with C383 MAIN. Only some chips or parts are different from each other due to different producers. Power supply board C383 PSB PSE The printer mechanism for Stylus COLOR 680 777 777i is designed newly. But, the basic component of the printer mechanism is same as previous...
Adjustment Program feature
This adjustment program is exclusive for Windows the OS that allows operation of this program is Windows 98. The following shows programs included in this program. I This adjustment program operates only under Windows 98 This program does not operate under DOS or Windows 3.X, 95, NT. I This adjustment program automatically install the appropriate program according to your OS. I Perform this adjustment program using parallel I F port or USB. The adjustment program enables you to set various...