Cns
No Paper Paper is not loaded correctly Figure 3-2. Paper is not loaded correctly Figure 3-2. Paper is not loaded correctly 1 Reload the paper, then click the Continue button. 2 If you want cancel the print job, click the Cancel button. 1 Click the Eject button to eject any jammed paper. printer, click the Stop button to cancel the print job. Then, open the printer cover and remove the jammed paper. NOTE If this error is indicated on the monitor, you can continue the printing until the I C...
EEPROM check function
You can check the EEPROM data or can write the specific data into the specific address of the EEPROM directly even if the printer is error condition. In case one of the main logic circuit such as CPU, I F receiver IC, RAM, EEPROM is broken, this function is not available Select the EEPROM check function in the Maintenance menu. The main menu of this function is as following figure. The following three function is built in this program. You can check the following information stored in the...
Operating Principles
This section describes the operating principles of the printer mechanism and electrical circuit boards. The Stylus COLOR 580 has only the following two circuit boards and dose not have control panel Main board C379MAIN-C or C379MAIN-B 1 Power supply board C367 PSB PSE NOTE 1 C379MAIN-B board is used for the product in the first mass production and it will be changed to C3 79MAIN-C board at an early date. The major difference is that C379MAIN-C has one chip CPU which include the ASCI function....
LD Roller removal
1. Remove the Housing from the printer. Section 4.2.1 Housing removal 2. Take the Head FFC off from the Head FFC holder located along the LD roller shaft holder. 2. Take the Head FFC off from the Head FFC holder located along the LD roller shaft holder. Figure 4-21. Taking Head FFC out from the FFC holder Figure 4-21. Taking Head FFC out from the FFC holder 3. Remove two screws C.B.S. 3x6, F Zn screw securing the LD roller holder to the Main frame. 3. Remove two screws C.B.S. 3x6, F Zn screw...
Envelope
No.10 241.3 mm x 104.8 mm DL 220 mm x 110 mm C6 162 mm x 114 mm 4x 6 220mm x 132mm ASF hopper available capacity 10sheets A6 Index card 105mm x 148mm A5 Index card 148mm x 219mm 5 x 8 Index Card 127mm x 203mm 10 x 8 Index card 127mm x 203mm ASF hopper available capacity 30sheets NOTE Envelope printing is available only in the normal temperature. Keep the longer side of the envelope horizontally at setting.
Change lever unit
Figure 4-56. Removing the Gears from ASF frame unit Figure 4-56. Removing the Gears from ASF frame unit 5. Remove the Compression Spring 2.67 located between the ASF Frame and the Hopper, and remove the Hopper from the ASF frame. 5. Remove the Compression Spring 2.67 located between the ASF Frame and the Hopper, and remove the Hopper from the ASF frame.
Check the EEPROM data
You can check the specific data stored in the specific address of the EEPROM. Input the specific address with hexadecimal code by referring Section 7.1.2 on page 132 EEPROM map . Use this function in your analysis usefully. You can change the specific data stored in the specific address of the EEPROM. However, do not use this function except the special case. Careless usage causes any trouble. You can change the specific data stored in the specific address of the EEPROM. However, do not use...
Hardware Initialization
This printer initializes itself when it is turned power on or printer recognized the Reset command D4 command . 0n this initialization, following actions are performed. Initialize printer mechanism Clear the input data buffer Initialization command, ESC also initializes the printer. 0n this initialization, following actions are performed. This printer initializes itself when the printer receive the IEEE1284.4 reset command or the USB cable is pull off. 0n this initialization, following actions...