Ribbon Advance Mechanism
The ribbon is held between the ribbon advance roller ribbon driven gear and the ribbon pressure roller. When the carriage moves from left to right and vice versa on the CR guide shaft, the timing belt turns the belt-driven pulley. Then the torque is transmitted to the ribbon driving gear through the gear trains. The ribbon driving gear rotates counterclockwise, no matter what direction the carriage moves, because a planetary gear is used in the gear linkage. Table 2-4. Ribbon Advance Gear...
Tlcn 1
Figure 1-14 C165 PSB PSE Board Assembly This board function is the control panel for the LQ-2170. It consists of a power switch, six buttons, and 10 indicator LEDs. This board is almost same as it for the LQ-2170. The printer mechanism consists of an 24-pin impact dot head, paper feed PF motor, ribbon feed RF motor, paper end PE sensor, home position HP sensor, platen gap PG sensor, release lever sensor, etc. This consists of printer cover assembly, edge guide assembly, upper housing, lower...
Info Vni
1 Plain paper weight 82 g m , 22 lb or recycled paper, except for A3-size paper. 2 Plain paper weight 82 g m2 , 22 lb or recycled paper, A3 paper. 3 Plain paper weight 64 g m2 , 17 lb , except for A3 paper. 4 Plain paper weight 64 g m2 , 17 lb , A3 paper. 5 Envelopes weight 91 g m2, 24 lb 6 Envelopes weight 45 g m2, 12 lb 7 Card stock weight 192 g m2, 51 lb thickness 0.22 mm, 0.0087 8 1 original 5 copies thickness 0.36 mm, 0.0142
Table of Contents Wyv
A.1. EXPANDED PRODUCTION COMMANDS A-1 A.5 CIRCUIT BOARD COMPONENT LAYOUTS A-17 Figure A-2. C165MAIN Board Assembly Circuit Figure A-3. C165 PSB Board Assembly Circuit Figure A-4. C165 PSE Board Assembly Circuit Figure A-5. C165MAIN Board Assembly Component Figure A-6. C165 PSB Board Assembly Component Figure A-7. C165 PSE Board Assembly Component Figure A-8. LQ-2170 Exploded Diagrams Figure A-9. LQ-2170 Exploded Diagrams Figure A-10. LQ-2170 Exploded Diagrams Figure A-11. CSF Bin 1 Exploded...
Main Components
1.6.2 C165 PSB PSE Board Assembly 1-36 Figure 1-1. Exterior View of the LQ-2170 1-2 Figure 1-3. Printable Area for Cut Sheets 1-9 Figure 1-4. Printable Area for Envelopes and Card Stock 1-11 Figure 1-5. Printable Area for Continuous Paper 1-13 Figure 1-7. Printable Area for Roll Paper 1-15 Figure 1-8. Data Transmission Timing 1-22 Figure 1-11. Hexadecimal Dump Printout 1-32 Figure 1-13. C165 MAIN Board Assembly 1-36 Figure 1-14. C165 PSB PSE Board Assembly 1-36 Figure 1-15. C165 PNL Board...
Removing the PW Sensor Assembly
1. Remove the printer cover and ribbon cartridge see Section 3.2.1 . 2. Remove the CB screw 2.5 x 5, F Zn securing the PW sensor to the ribbon mask holder. Then, remove the FFC from the PW sensor connector, mounted onto the CR cover. 3. Remove the PW sensor assembly along with the CR cover by pushing and releasing the 2 clips for the CR cover, as shown in the following figure.
TPE Level Reset
This section describes the procedure to reset the TPE top paper end level. This operation is required when the PW sensor assembly is replaced, and if it is not performed, the printer does not recognize that the PW sensor has been replaced, thus, limiting the ability of the new sensor to operate. This reset operation can be performed only from the Settings Diskette. Note After this operation, the reset value for the TPE LEVEL is printed out automatically. Check that the reset value is FF. 1....
System Reset Circuit
Control circuits IC1 and IC2 are initialized when a RESET signal LOW level is output from port 1 VOUT of IC10. IC10 monitors the 5 V line on port 3, and resets under the following conditions 1. When the power supply is turned on, a RESET signal is output. RESET is canceled when the 5 V line goes up to 4.2 V, and then 100 ms passes. 2. When the 5 V line goes below 4.2 V, a RESET signal is output. RESET is canceled when the 5 V line goes back up to 4.2 V and then 100 ms passes. 2. When the 5 V...
Pc
Page Format Tractor Rear Front Friction , CSF Bin 1 Bin 2 , Manual Feed Rear Front Friction Bin 1 , Tractor Tear-Off Status Off 1.4.9 Bidirectional Adjustment Function Pressing the button while turning on the printer puts the printer in bidirectional adjustment mode. In this mode, you can adjust the bidirectional alignment for the following three modes For instructions on performing the adjustment, see Chapter 4. This initialization is activated by the control code . This initialization Resets...
Removing the Case Open Sensor Assembly
1. Remove the rear edge guide assembly, paper eject assembly, rear tractor unit, and printer cover see Section 3.2.1 . 2. Remove the panel board see Section 3.2.2 and upper housing assemblies see Section 3.2.7 . 3. Turn the upper housing assembly over and remove the case open sensor assembly by loosening the CBB screw 3 x 8, F Zn fixing the sensor holder to the upper housing assembly.