Levelness Adjustment of the Bin Unit
1. Remove the covers from the both legs of the 10-Bin Unit. 4. If the knob is turned counterclockwise, the 10-Bin Unit moves in the direction shown in the figure below. 3. Turn the knob attached to each leg of the unit to adjust its standing position. 5. After the standing position has been adjusted, tighten the wing bolts. 6. Reinstall the covers onto the legs of the 10-Bin Unit.
Vertical Transport Roller Removal
1. Remove the outer covers. See Section 5.2.1. 2. If the Vertical Transport Roller gear 17T to be removed is inner side of the following parts, remove that part. Transport Motor Section 5.2.2.19 Sorter Set Switch Section 5.2.2.3 Controller board bracket Section 5.2.2.4. 3. Remove two screws 3508 securing each support plate to the frame and remove the support plates along with the jammed paper remove guide. 4. Remove two E-rings 9125 from both edges of the Vertical Transport Roller. 5. Unhook...
Bin Bin Switch Solenoid SL Removal
1. Remove the Rear Cover. Refer to Section 4.2.2. 2. Remove the Control Board. Refer to Section 4.2.6. 3. Release the harness from the cable clamp in the bracket. 4. Remove six screws 3501 securing the bracket to the unit frame and remove the bracket. 5. Remove the screw 3501 securing the bracket for the Bin 4 Bin 5 Switch Solenoid to the unit frame and remove the bracket along with the jammed paper remove door sensor. 6. Remove two screws 1305 securing the Bin 4 Bin 5 Switch Solenoid to the...
Bin Bin Switch Mechanism
When the Bin 4 or Bin 5 is selected as the paper exit, paper from the printer is transported to the selected bin by way of the Transfer Switch Guide Lever Bin 1 , Paper Guide, and Vertical Transport Roller that moves paper up, and Bin 4 Bin 5 Switch Guide. The Bin4 Bin 5 Switch Guide switches the paper path to the selected bin according to the Solenoid's on off operation. Figure 6-51. Bin 4 Bin 5 Switch Mechanism In the shift mode, paper is ejected to the Bin 1. When the Bin 1 Shift Motor M2...
Shift Guide Plate Removal
1. Remove the Front Cover and the Rear Cover. Refer to Section 4.2.1 and Section 4.2.2. 2. Remove the Shift Motor along with the bracket. Refer to Section 4.2.4. 3. Remove the Transport Motor along with the bracket. Refer to Section 4.2.9. 4. Remove the Transfer Switch Solenoid along with the bracket. Refer to Section 4.2.11. 5. Remove the Bin 1 Guide, gear 24T, pin 0535 , and the Eject Sensor Board. Refer to Section 4.2.15. 6. Remove the screw 4005 and five screws 3501 securing the Shift Guide...
Paper Separation Mechanism
Each cassette has fingers that function to separate the top sheet of paper from the rest of the paper stack at paper take-up. This mechanism uses the fingers and the Paper Take-up Roller on the both edges of the cassette. When the Paper Take-up Roller starts turning to take up the top sheet of paper, its turning force is directly transmitted to the top sheet of paper as it is in direct contact with the Paper Take-up Roller. This force forms paper loop that overcomes the block of the fingers,...
Paper Separating Mechanism
The paper separating mechanism employs a system with a torque limiter that is fitted to the Separator Roller shaft and stops the Separator Roller when there is a change in friction between the Feed and Separator Rolls. When only one sheet of paper is fed, the friction coefficient on the top side of the paper is equal to that on the underside. Driven by the Feed Roller, the paper drives the Separator Rollers. This causes the paper to be sent to the Vertical Transport Section. The friction...
Horizontal Transport Unit A
Table 5-24. Parts List - Horizontal Transport Unit A
Mechanical Operations Paper Exit Path 1
The paper exit path for the paper output from the printer varies depending on the paper ejection mode. Sensors and switches monitors if the paper is being transported along the correct path. The paper paths and involved parts are as shown in the following figure. When the 10-bin Unit is used, the entry part of the Horizontal Transport Unit is lowered by the Paper Path Switch Solenoid's operation to send paper out to the Bin 1. In the sort mode, the entry part of the Horizontal Transport Unit is...
NonSort Bin Jam Sensor PC Removal
1. Remove the Rear Cover. See Section 5.2.3.1. 2. Flip the Horizontal Transport Unit. 3. Remove two screws 3704 securing the Non-Sort Bin Jam Sensor cover to the Horizontal Transport Unit and remove the cover along with the sensor. 4. Remove the harness from the connector on the sensor. 5. Remove the rubber retaining ring from the actuator pin in the Non-Sort Bin Jam Sensor and remove the pin, actuator, and torsion spring. 6. Unhook the Non-Sort Bin Jam Sensor from the cover and remove Figure...